Skip to content
Find a tool

Tattoo Stencil Maker

Create a line stencil for transfer paper, mirrored and sized in millimetres.

Free · runs in your browser · nothing is uploaded

Open on Outlinecut

This embed was switched off for this website. Open on Outlinecut

Add this tool to your siteFree embed code, no sign-up. Keep the credit link.

Embed this tool

Copy this code into your website, blog or class page. The tool runs inside your page.

Optional settings, added to the address after embed=1: &accent=0f6b5c (colour, 3 or 6 hex digits). Other parameters are ignored.

Please keep the credit link below the tool.

This tattoo stencil maker draws the picture’s edges as black lines on white paper and prepares a transfer sheet at the size you set in millimetres. The sheet is 300 dpi and mirrored by default, for transfer methods where the printed side is pressed onto the skin; whether your method needs the mirror is worth checking with a test print before every new setup. You choose the line detail, the amount of line and how thick the lines are, then download the sheet as a PNG, or the same lines as an SVG or PDF. What you get is a line drawing of your picture, not a finished tattoo design, so pick a source whose shapes you want to keep.
Tattoo stencil maker example

How to use the Tattoo Stencil Maker

  1. Drop a picture on the tool, paste one, or press Choose image. Try a sample loads a demo.
  2. Set Width (5 to 600 mm, default 120) to the width of the stencil on skin.
  3. Adjust Line detail (blur) (0.5 to 4, default 1.2). Low values pick up fine detail, and high values keep only broad shapes.
  4. Adjust Line amount (-40 to 40, default 0) in small steps. Negative values keep only the strongest edges. Positive values add lines quickly, so try one or two steps at a time.
  5. Raise Thicken lines (0 to 4, default 0) if the lines are too thin to read on a printout.
  6. Use Brightness and Contrast (-100 to 100) to separate the subject from the background. Tick Invert if the picture has light lines on a dark ground.
  7. Leave Mirror for transfer paper ticked when the sheet goes on thermal transfer paper. Untick it for a sheet that should read normally.
  8. Read the Sheet line under the preview: it shows width, height and dpi.
  9. Press Download PNG for the print-ready sheet, or Download SVG or Download PDF for the lines as vectors.

Print a test on plain paper first and check the size with a ruler before you use transfer paper. If the lines are too faint or too heavy, return to steps 3 to 5.

How do I make a tattoo stencil from a photo?

Load a photo with a clear subject, set the sheet width, and adjust the line controls until only the outline and details you want remain. Then print the PNG on your transfer paper. The picture is reduced to at most 1,400 px on the long side, converted to lines with an extended difference-of-Gaussians filter, and redrawn at 300 dpi at your width.

  1. Choose a photo or sketch with a clear subject and good light.
  2. Lower Line detail (blur) for fine detail, raise it to drop noise and texture.
  3. Move Line amount a step or two at a time while watching the preview.
  4. Thicken lines slightly if fine lines vanish when printed.
  5. Check the mirror setting, then download.

What does the transfer sheet contain?

Download PNG gives a black-and-white sheet, white paper with black lines, drawn at 300 dpi. Its pixel size follows from your width, as the table shows. The PNG file itself carries no dpi tag, so print it at 300 dpi or 100 % (actual size, not fit to page), or print the PDF, which is sized in millimetres. Both SVG and PDF hold the same lines as vector shapes.

WidthSheet size in pixels (wide)
60 mm709
120 mm (default)1,417
200 mm2,362
300 mm3,543

The source picture is limited to 1,400 px, so a sheet wider than about 118 mm is enlarged, not sharper. Lines stay solid black, but fine detail will not increase.

Why is the sheet mirrored?

Each transfer step that presses an image face-down reverses it. When the printed or inked side of the sheet goes onto the skin, the print has to be mirrored so the stencil reads the right way round, which is why the box is ticked by default. Some thermal copiers and stencil printers already reverse the image during the transfer, and then the mirror must be off, or the stencil and the tattoo come out reversed. The tool cannot know your setup: write a letter on a test picture, run it through your full process on plain paper, and only then use the sheet on skin. Text and numbers show the effect most clearly.

How thick will the lines be?

Thicken lines grows every line by that many pixels of the analysis image, so physical thickness depends on the width. For a source at least 1,400 px wide, one step adds about the width divided by 1,400 on each side of the line.

WidthOne step adds (each side)
60 mmabout 0.04 mm
120 mmabout 0.09 mm
200 mmabout 0.14 mm

Can I use the stencils commercially?

The Terms page says what you generate is yours to use, including commercially, with no credit needed. You are still responsible for the rights to the picture you start from.

Answers to common questions

What kinds of images work best?

Photos and drawings with a clear subject, good light and a plain background give the cleanest lines. Colour and gray pictures are converted automatically, but a blurry picture has weak edges, so expect fewer and fainter lines.

Which printers work, and do I need special paper?

The tool makes a mirrored black-and-white sheet meant for thermal transfer paper. It does not drive any printer, so choose one that suits your transfer paper. The sheet itself is a plain black-and-white image at 300 dpi.

What file formats can I download?

PNG for the print sheet at 300 dpi, and SVG or PDF for the lines as vectors. The SVG and PDF are mirrored when the mirror box is ticked.

Is there an app?

No install is needed. The tool is a web page and runs in your browser, and your picture stays on your device.

Can I edit the stencil after it is made?

There is no editor on the page. Change the sliders and the sheet updates, or open the SVG in a vector editor to remove lines by hand.

How long does it take?

That depends on your device and the size of the picture. The engine also loads the first time you use the tool, so the first result takes a little longer.

Does it design the tattoo?

No. It traces the lines already in your picture. Placement, size and shading decisions stay with you and your artist.