Skip to content
Find a tool

Die Cut Line Generator

Add a cut line around transparent PNG art or a dark shape, with the offset in millimetres and the total cut length shown.

Free · runs in your browser · nothing is uploaded

Open on Outlinecut

This embed was switched off for this website. Open on Outlinecut

Add this tool to your siteFree embed code, no sign-up. Keep the credit link.

Embed this tool

Copy this code into your website, blog or class page. The tool runs inside your page.

Optional settings, added to the address after embed=1: &accent=0f6b5c (colour, 3 or 6 hex digits). Other parameters are ignored.

Please keep the credit link below the tool.

A die cut line generator draws the path a blade follows around your artwork. This one builds the line from the picture’s silhouette, either the transparent pixels of a PNG or the dark shape of an image without transparency, and grows it outward by a distance you set from 0 to 20 mm. The outline downloads as SVG, DXF or PDF, drawn as a red hairline so cutting software reads it as a cut path, and the total cut length appears in millimetres. The same outline works for any printed shape you cut out, not only stickers. The sections below explain die cut and kiss cut, how much border to leave and which file a cutter needs.
Die cut line generator example

How to add a cut line to an image

  1. Choose your picture, drop one on the tool or paste one from the clipboard. A PNG with a transparent background gives the cleanest silhouette, and Try a sample loads a test picture.
  2. Set Width (5 to 600 mm, default 100). This is the width of the whole picture frame, not just the artwork, and the height follows the picture.
  3. Drag Cut line distance (0 to 20 mm in 0.5 mm steps, default 3) to set the border between the artwork and the blade.
  4. Set Smooth edges (0 to 10, default 2) to soften jagged edges of the silhouette before the offset is applied.
  5. Leave Fill holes ticked, its default, so gaps inside the artwork are closed. Untick it if those gaps should be cut out as well.
  6. Adjust Smoothing (0 to 100, default 50) to smooth the final line; right-angle corners stay sharp.
  7. Check the outline in the Overlay view against the Original, and read the Cut length under the preview. It is the total length of the line in millimetres.
  8. Click Download SVG, Download DXF or Download PDF.

The line is exported as a red hairline with a 0.01 mm stroke and no fill. Open the file in your cutting software and check it before you cut.

What is a die cut line?

A die cut line is the path a blade follows to separate a printed sticker from its sheet. It runs a little outside the artwork, which leaves a thin border of material around the design. Here the line comes from the picture’s silhouette, grown outward by the Cut line distance, and it is a single closed outline.

The silhouette comes from the transparent pixels of a PNG. An image without transparency has none, so the dark shape is used instead. Smooth edges and Fill holes act on that silhouette before the outward growth.

What is the difference between kiss cut and die cut?

A die cut goes through both the sticker and its backing, so each sticker comes free of the sheet. A kiss cut goes through the top layer only and leaves the backing whole, so the stickers stay on one sheet. This tool draws one outline for both, and the cut depth is set on your cutter.

How much offset should a sticker cut line have?

Set Cut line distance to the border you want between the artwork and the blade. The default is 3 mm, and the range is 0 to 20 mm. The growth is measured the same in every direction, corners included, because it uses an exact Euclidean distance rather than a square brush. The line cannot leave the picture, so artwork that comes closer to the edge than the distance gets a thinner border there; the tool warns when that happens, and the fix is to add empty space around the artwork.

The line grows only inside the picture’s own frame, so leave a margin of at least the distance on every side. The table shows the smallest frame for artwork that is 60 x 40 mm.

Cut line distanceSmallest frame for 60 x 40 mm artwork
1 mm62 x 42 mm
3 mm (default)66 x 46 mm
5 mm70 x 50 mm
10 mm80 x 60 mm

If the artwork touches the edge of the picture, the outline is cut off there. Add transparent or white margin around it before you load it.

What file does a cutter need for a cut line?

Use whichever format your cutting software imports. All three downloads carry the same outline.

FormatButtonWhat you get
SVGDownload SVGRed 0.01 mm hairline, no fill
DXFDownload DXFThe outline as an R12 file in millimetres
PDFDownload PDFA vector page sized to the outline

Answers to common questions

Can I make a cut line from a PNG with transparency?

Yes. The outline follows the visible, non-transparent pixels, so the line hugs the artwork before the offset is added.

Can I add a cut line to a JPG?

Yes, but a JPG has no transparency, so the tool takes the dark shape as the artwork. Dark artwork on a light background works. A light subject on a white background does not.

Why is my cut line cut off at the edge?

The outline grows only inside the picture’s frame. If the artwork reaches the edge, there is no room for the offset. Add margin of at least the Cut line distance around it and load it again.

Should I keep Fill holes on?

For most stickers, yes. It closes gaps inside the artwork so the blade does not cut islands out. Untick it only when those gaps should be cut as well.

What is the difference between Smooth edges and Smoothing?

Smooth edges softens the silhouette itself, in pixels, before the outward growth. Smoothing rounds the corners of the finished line afterwards. Raise the first for ragged artwork edges and the second for a calmer outline.

What does the cut length tell me?

It is the total length of the outline in millimetres. Use it to compare settings, since a smoother line or a smaller distance shortens the path.