Single Line SVG
Turn a drawing into single pen strokes in a drawing order that saves pen travel.
Free · runs in your browser · nothing is uploaded
Recent
Your last 10 settings, saved only in this browser. Nothing is uploaded.

How to use the single line SVG tool
- Load a picture with Choose image, or drop or paste one. Dark lines on light paper work best.
- Leave Black and white threshold on automatic first. Move it between 1 and 255 only when lines break up or the background turns into specks.
- Tick Invert if your lines are light on a dark background.
- Set Width (5 to 600 mm, default 100) to the final size of the drawing.
- Set Stroke width (0.05 to 3 mm, default 0.3) to match your pen tip.
- Raise Drop strokes shorter than (0 to 60 px, default 6) to remove specks, and adjust Smoothing (0 to 100, default 50) for the curves.
- Keep Order strokes for the plotter ticked so the pen takes a shorter route between strokes.
- Set Feed rate (100 to 12000 mm/min, default 3000) to suit your machine. It changes the drawing speed in the G-code and the time estimate.
- Compare Original, Result and Overlay. Under the preview, read the stroke count and the drawing time in minutes.
- Press Download SVG, Download G-code, Download PDF or Download DXF.
Change one slider at a time. The stroke count and drawing time then show which setting made the difference.
Start with a clean drawing of thin dark lines. If your plotter needs a larger pen, raise Stroke width only after you are happy with the stroke count, so you can see the effect of each change.
What is a single line SVG?
A single line SVG stores each stroke as one open path with no fill, drawn as a line rather than a shape. This tool writes one path per pen stroke with round caps and joins. A plotter or cutter reads that as a line to follow, not an area to colour in.
How do I make a single line SVG from a drawing?
Load the drawing, then let the tool thin it: it turns the picture black and white with an automatic or manual threshold, reduces each dark line to its centre, drops strokes shorter than your limit and smooths the paths. Download the SVG.
The same steps as a checklist:
- Photograph or scan the drawing flat on light paper.
- Trace it with the defaults and view the Overlay.
- Raise Drop strokes shorter than until stray dots vanish.
- Set Stroke width for your pen and download.
What does the tool report for a real run?
After a trace the line under the preview lists the size, paths, nodes, strokes and, for this tool, the drawing time in minutes. On a small synthetic test image with the default settings it gave the values below. Your picture will give different numbers.
| Measure | Value |
|---|---|
| Paths | 5 |
| Strokes | 5 |
| Nodes | 26 |
| Drawing time | 0.3 min |
| Travel in file order, in image pixels | 802 |
| Travel after ordering, in image pixels | 373 |
| Pen-up travel computed for the G-code | 212 mm |
The last three rows come from the tool’s code and are not printed on the page. Ordering cut the route by 429 pixels, a bit over half.
What is the single line vs outline (double line) problem?
An outline traces the edge of a filled shape, so a pen draws two parallel lines for every stroke. A single line drawing keeps one centre line per stroke. This tool follows the middle of each line, so thin strokes come out as one path.
Hollow lettering is the exception: each border is thinned separately, so it still gives two lines.
What does the G-code do with the pen?
The G-code is written in millimetres with the origin at the bottom left. The pen is lowered and raised with servo-style commands (an M3 value followed by a short pause), which suits plotters that use a servo for the pen: M3 S1000 lowers the pen and M3 S0 raises it, with a 0.15 s pause after each. Those values must match your plotter’s firmware. Never run this file on a laser machine, where M3 S1000 means full laser power along every stroke. It has not been run on a real plotter, so check the file against your controller and try it with the pen lifted first.
Answers to common questions
How do I make an SVG that cuts or draws only single lines?
Set Stroke width to the line weight you want, raise Drop strokes shorter than until tiny fragments disappear, and download the SVG. Every stroke is an open path with no fill.
How do I get Cricut to draw a single line?
This tool has no Cricut export. Import the SVG into Design Space and choose the Draw operation for the layer so the pen follows the line.
Can I use the file with a pen plotter?
Yes. Download the G-code for plotters that take it, or the SVG for software that reads SVG directly. AxiDraw’s software reads SVG files, according to its CLI documentation.
Can I get a single line font from this?
There is no font feature. The tool works from a picture, so text in a picture is thinned like any other drawing. Bold, solid letters give clean centre lines; outlined letters give two.
Why is a letter or shape traced twice?
A hollow shape has two borders, and each border is thinned separately. Fill the shape solid in the source picture and trace again.
Does the file leave my computer?
No. The work happens in your browser and the page makes no upload request.
Related tools
- Centerline Tracing: use it when you want the same strokes as SVG, PDF, DXF or PNG without plotter G-code.
- Signature to SVG: use it to turn a signature photo into one clean stroke path.
- Photo to Line Art: use it to draw a photo as lines first, then bring the result here.
- Line Art Converter: use it to clean a scanned sketch before tracing it.
- Photo to Outline: use it when you need the outer edge of a subject instead of a middle line.
- Photo to Stencil: use it when you want solid cuttable shapes with bridges.
- Image to G-code: use it to engrave a picture with a laser rather than draw lines with a pen.
- Convert Image to Cut File: use it for filled cut files for cutting machines.