Skip to content
Find a tool

Laser Engraving Image Converter

Prepare a photo for a diode or CO2 laser: set the width and line density, choose a dither, and see the burned area.

Free · runs in your browser · nothing is uploaded

Open on Outlinecut

This embed was switched off for this website. Open on Outlinecut

Add this tool to your siteFree embed code, no sign-up. Keep the credit link.

Embed this tool

Copy this code into your website, blog or class page. The tool runs inside your page.

Optional settings, added to the address after embed=1: &accent=0f6b5c (colour, 3 or 6 hex digits). Other parameters are ignored.

Please keep the credit link below the tool.

A laser engraving image converter resamples a photo to your width and line density, adjusts the grey tones and dithers the result to 1 bit, so every pixel is either burned or left alone. Black pixels are the ones the laser burns. You choose the width in millimetres, set how many lines per millimetre to use, pick one of eight dither methods and watch the burned-area percentage change. The downloads are a 1-bit BMP, a PBM and a PNG. The BMP carries a resolution of lines per mm times 25.4 dpi, so laser software can place it at the right size. The sections below compare the dither methods, work out lines per mm in dpi and pixels, and cover the file formats and the size cap.
Laser engraving image converter example

How to prepare a photo for engraving

  1. Choose your photo, drop one on the tool or paste one from the clipboard. Try a sample loads a test picture if you only want to see the tool work.
  2. Set Width (5 to 600 mm, default 80) to the width of the piece you will engrave. The height follows the photo.
  3. Set Line density (2 to 20 lines/mm, default 10). It controls how many pixel rows the laser gets per millimetre.
  4. Pick a Dithering method. Floyd-Steinberg is the default. No dithering (threshold) gives a plain two-tone image.
  5. Adjust Brightness and Contrast (both -100 to 100, default 0) and Gamma (0.3 to 3, default 1) until the tones look right.
  6. Use Black and white threshold (0 to 255, default 128) to shift the overall darkness. For No dithering it is the cut-off between burn and no burn.
  7. Tick Invert if the areas you want burned are currently white.
  8. Read Burned area % under the preview, then click Download 1-bit BMP, Download PBM or Download PNG.

Compare the Original and Result views. A photo with strong contrast and a clear subject gives the best engraving. The line under the preview shows the size in millimetres and the burned area, so you can judge how dark the piece will be before you download anything.

What is the best dithering for laser engraving photos?

No single method suits every photo. Floyd-Steinberg is the default, and it spreads each pixel’s rounding error to its neighbours, which usually keeps smooth tones. Try two or three methods on the same photo and compare the burned-area percentage and the preview before you burn anything.

MethodTypeTypical look
Floyd-SteinbergError diffusionSmooth tones, fine grain
AtkinsonError diffusionHigher contrast, crisper edges
Jarvis, Stucki, SierraError diffusionWider spread, smoother and less noisy
Bayer 4x4, Bayer 8x8OrderedA regular dot pattern
No dithering (threshold)Cut-offPlain two-tone silhouette

What lines per mm should I use?

Line density is the number of pixel rows per millimetre. Dpi equals lines per mm times 25.4, and the default of 10 means a 0.1 mm line interval, which is 254 dpi. What your laser and material want depends on its beam spot, and this tool cannot know that, so test on scrap. A line interval much finer than the spot only overlaps burns. The table works out the numbers for an 80 mm wide piece.

Lines per mmLine intervaldpiPixels across 80 mm
20.5 mm50.8160
50.2 mm127400
10 (default)0.1 mm254800
150.067 mm3811,200
200.05 mm5081,600

The long side is capped at 4,000 pixels. Past that the picture is shrunk, so the real density is lower than the slider says. The BMP then stores the real, lower dpi (4,000 pixels divided by the width), so it still imports at the width you set, only with less detail. At 10 lines/mm the cap is reached at 400 mm, and at 20 lines/mm at 200 mm.

What file format does LightBurn or xTool want?

Both import bitmaps. LightBurn lists PNG, JPG, BMP, GIF and TIF, and xTool Creative Space lists PNG, JPG and BMP, according to their documentation read on 2026-10-26. Glowforge takes PNG and JPG for engraving. That makes the BMP and the PNG the safe downloads, and the PBM a format for software that reads it.

DownloadResolution stored in the file
1-bit BMPLines per mm times 25.4 dpi
PBMNone
PNGNone, so set the size in your software

Answers to common questions

Why convert to black and white first?

A laser either burns a spot or it does not. Dithering turns grey tones into a pattern of burned and unburned pixels that the laser can follow.

How do I invert an image for laser engraving?

Tick Invert. Black pixels are the ones burned, so inverting swaps which areas the laser marks.

Can I use my own dpi value?

Not typed in directly. Line density runs from 2 to 20 lines/mm, which gives 50.8 to 508 dpi, and the BMP stores the matching value (lower only when the 4,000 pixel cap applies).

What does Burned area % mean?

It is the share of pixels in the result that are black, which are the ones the laser burns. A higher number means a darker engraving and a longer job.

How do I get a good portrait engraving?

Start with a high-contrast photo where the face is clear. Use Contrast and Gamma to keep the eyes and edges distinct, then compare two dither methods before you commit.

How do I choose the output size?

Set Width to the physical width of the piece. The pixel width of the result is that width times the line density. For an 80 mm piece at 10 lines/mm the result is 800 pixels wide, as in the table above. The height follows the photo.

Can you laser engrave images?

Yes. A laser burns dots or lines in a pattern, so a photo has to become a black and white pattern first, and that conversion is what this tool does.

Should I use the BMP or the PNG?

The BMP when your software reads size from the file, since it carries the dpi. The PNG has no resolution value, so you set the size in the software yourself.