Skip to content
Find a tool

Silhouette Cameo SVG Converter

Trace a picture into cut-ready paths, see whether it fits the Cameo 5 area, and download SVG or DXF R12.

Free · runs in your browser · nothing is uploaded

Open on Outlinecut

This embed was switched off for this website. Open on Outlinecut

Add this tool to your siteFree embed code, no sign-up. Keep the credit link.

Embed this tool

Copy this code into your website, blog or class page. The tool runs inside your page.

Optional settings, added to the address after embed=1: &accent=0f6b5c (colour, 3 or 6 hex digits). Other parameters are ignored.

Please keep the credit link below the tool.

To make a Silhouette Cameo SVG from an image, the picture is traced into flat colour regions, each colour is merged into one closed path, and the result downloads as an SVG that Silhouette Studio opens in Designer Edition or higher. You set the width in millimetres, choose how many colours to keep and clean up specks before exporting. A size check compares the design with the Cameo 5 operating area, and a DXF download is there for software that prefers it. Clear shapes with a handful of colours trace best, while photos come out as flat colour regions without shading. The sections below explain which Studio editions open SVG, how large a Cameo 5 design can be and how to get fewer points.
Convert image to svg for silhouette example

How to turn an image into a Silhouette SVG

  1. Choose a picture, drop one on the tool or paste one from the clipboard. Try a sample loads a test picture if you only want to watch the trace.
  2. Set Width (5 to 600 mm, default 100). The height follows the picture, and the note under the preview says whether the size fits the Cameo 5 area. Width is the width of the whole picture, empty margin included; the shapes keep their place inside it, so a logo with a white border comes out narrower than this figure (crop the picture tight if the shapes must be exactly this wide).
  3. Set Colors (1 to 12, default 4). Fewer colours mean fewer layers to cut.
  4. Keep Remove the background ticked, its default, so the backdrop is not traced. Untick it only when the background is part of the design.
  5. Raise Remove specks up to (0 to 40, default 8) to clear stray dots, and set Smallest feature (0 to 5 mm, default 0.5) to drop pieces too small to cut.
  6. Adjust Smoothing (0 to 100, default 50) and Contrast (-100 to 100, default 0). Tick Invert only if the trace follows the wrong side.
  7. Pick a DXF version, R12 (the default) or R2000, if you plan to use the DXF.
  8. Open the Overlay view to check the outlines against the original.
  9. Click Download SVG, Download DXF or Download PDF.

The Silhouette preset writes coordinates with three decimals and keeps layers from overlapping. Watch the Paths, Nodes and Colors readout under the preview while you adjust.

Can Silhouette Studio Basic open SVG?

No. According to Silhouette America’s Studio page, which we read on 2026-10-26, Silhouette Studio opens SVG files only in Designer Edition or higher and saves SVG only in Business Edition. Basic Edition sits below that line, so check which edition you run before you rely on an SVG.

EditionOpens SVGSaves SVG
BasicNoNo
DesignerYesNo
Designer PlusYesNo
BusinessYesYes

Silhouette’s page did not confirm which edition opens DXF, so this page makes no promise about it. The DXF download is something to try in your own copy of Studio, not a verified fallback for Basic.

How do I import an SVG into Silhouette Studio?

Download the SVG and open it with Studio’s Open command, which works in Designer Edition or higher. Basic Edition will not open it. Before cutting, compare the design’s width and height with your mat, because the file keeps the size you set here.

  1. Click Download SVG.
  2. Confirm that your Studio edition is Designer or higher.
  3. Open the downloaded file in Studio.
  4. If the design is too big for the mat, lower Width and download it again.

What size can a Cameo cut?

Silhouette lists a guaranteed operating area of 12 x 24 in for the Cameo 5, which is 304.8 x 609.6 mm. The size check compares your result with that area and lets the design turn 90 degrees, so a design passes if it fits either way round. The table shows how the rule plays out.

Design (mm)Cameo 5 check
600 x 300Fits when turned
305 x 100Fits when turned
304.8 x 609.6Fits exactly
610 x 100Too long
400 x 400Too wide

The Width slider stops at 600 mm, just under the 609.6 mm long side.

How many colours should a Silhouette SVG have?

Use one colour for each material you plan to cut. Colors counts cut colours only, the removed background is not counted, and each colour becomes one layer. Colors is a maximum: when two shades are close the tracer merges them, and a colour close to the background can merge into it and drop out, so count the layers in the Overlay view. The background that Remove the background drops is the colour along the picture’s edge (white, cream paper or a plain coloured backdrop); if the artwork itself runs off every edge, white is treated as the background. The default is 4 and the range is 1 to 12.

Start with the number of materials you own, then look at the Overlay view. If two similar shades merge, raise Colors by one. If thin slivers appear, lower it or raise Smallest feature.

Why does my traced SVG have too many points?

Every curve in a trace is stored as nodes, and busy pictures need many of them. To cut the count, lower Colors, raise Remove specks up to, and raise Smallest feature so tiny pieces disappear. The Nodes readout under the preview shows the effect after each change.

Answers to common questions

Do I need Designer Edition for SVG?

To open SVG files in Silhouette Studio, yes: Designer Edition or higher. Saving SVG from Studio needs Business Edition.

Does Silhouette use SVG or PNG?

Studio opens SVG in Designer Edition or higher. This tool gives you SVG, DXF and PDF downloads, and this page does not cover PNG import in any edition.

What is DXF R12 and when should I use it?

R12 (AC1009) is the oldest widely read DXF version and the default here. R2000 (AC1015) is the newer option. Pick the one your software accepts, and test it with a small design.

How can I convert a JPEG to SVG for Silhouette?

Choose the JPG, set Width and Colors, then click Download SVG. A PNG or any other picture your browser can open goes through the same steps.

Why convert a PNG to SVG?

A PNG is a grid of pixels with no cut path. An SVG stores outlines, so a cutter can follow them and the design can be resized without soft edges.

Can I control the colours in the SVG?

You control how many: Colors keeps 1 to 12 colour regions, each merged into one layer. The tool picks the shades itself from the picture.