Skip to content
Find a tool

Convert Image to SVG for Cricut

Upload a PNG or JPG, pick how many colors to cut, and download an SVG that Design Space splits into clean layers.

Free · runs in your browser · nothing is uploaded

Open on Outlinecut

This embed was switched off for this website. Open on Outlinecut

Add this tool to your siteFree embed code, no sign-up. Keep the credit link.

Embed this tool

Copy this code into your website, blog or class page. The tool runs inside your page.

Optional settings, added to the address after embed=1: &accent=0f6b5c (colour, 3 or 6 hex digits). Other parameters are ignored.

Please keep the credit link below the tool.

To convert an image to SVG for Cricut, the picture is traced into flat colour regions, each colour is merged into one closed path, and the backdrop is dropped. You pick how many colours to keep and the width in millimetres, then download an SVG that Design Space splits into one layer per colour. PNG, JPG and phone photos all work as input. A size check compares the result with the Cricut Maker 4 mat, and DXF and PDF downloads sit next to the SVG. Photos with a clear subject and a few tones trace best, while a shaded portrait turns into poster-like shapes. The sections below cover the Design Space upload, mat size and a sensible colour count.
Convert image to svg for cricut example

How to turn an image into a Cricut SVG

  1. Choose a picture, drop one on the tool or paste one from the clipboard. Try a sample loads a test picture if you only want to see the tool work.
  2. Set Width (5 to 600 mm, default 100). The height follows the picture, and the line under the preview shows the size in mm and says whether it fits the Cricut mat. Width is the width of the whole picture, empty margin included; the shapes keep their place inside it, so a logo with a white border comes out narrower than this figure (crop the picture tight if the shapes must be exactly this wide).
  3. Set Colors (1 to 12, default 4). Each colour becomes one cut layer.
  4. Keep Remove the background ticked, its default, so the backdrop does not become a layer.
  5. Raise Remove specks up to (0 to 40, default 8) to drop stray dots, and set Smallest feature (0 to 5 mm, default 0.5) to drop pieces too small to cut.
  6. Adjust Smoothing (0 to 100, default 50) for rounder curves, and Contrast (-100 to 100, default 0) for faded pictures. Tick Invert only if the trace follows the wrong side.
  7. Open the Overlay view to see the outlines on top of the original, and read the line under the preview. It lists the size in mm, the paths, the nodes and the colours.
  8. Click Download SVG. Download DXF and Download PDF are available too.

How do I upload an SVG to Cricut Design Space?

Download the SVG here and add it through the Upload option in Design Space. Design Space splits a vector file into layers on import, so every colour from this tool arrives as its own layer. A PNG or JPG uploaded directly stays a single layer, which is why the trace comes first.

Cricut’s own upload guide lists SVG, DXF, PNG, JPG, BMP and GIF as accepted upload formats; we read that list on 2026-10-26. Cricut’s help pages could not be read by our checks, so upload size limits and the smallest cut Design Space allows are not stated here. Look them up in Design Space before a large project.

What size can a Cricut cut?

The size check compares the width and height of your result, in millimetres, with the Cricut Maker 4 mat and lets the design turn 90 degrees. A design that matches the limit exactly still fits. Cricut lists the figures below on its Maker 4 page.

SurfaceListed sizeIn mm
Maker 4 mat11.5 x 23.5 in292.1 x 596.9
Maker 4 Smart Materialsup to 11.7 in x 12 ftup to 297.2 x 3,657.6

The check uses the mat only. Two cases show how it behaves. A 500 x 250 mm design passes because it fits once turned. A 300 x 300 mm square fails even though 300 is far below 596.9, because the mat is only 292.1 mm across. The Width slider goes up to 600 mm, which is longer than any side of the mat, so read the fit message before you cut.

How many colours should a Cricut SVG have?

Use one colour for each material you plan to cut, and no more. Colors counts cut colours only, and the removed background is not counted. Colors is a maximum: when two shades are close the tracer merges them, and a colour close to the background can merge into it and drop out, so count the layers in the Overlay view. The background that Remove the background drops is the colour along the picture’s edge (white, cream paper or a plain coloured backdrop); if the artwork itself runs off every edge, white is treated as the background. The default is 4 and the range is 1 to 12. Each colour is one layer, so every extra colour is another sheet of vinyl or paper to cut and stack.

Start with the number of materials you own, then check the Overlay view. If two similar shades merge, raise Colors by one. If thin slivers appear, lower it or raise Smallest feature.

Answers to common questions

Does image to SVG work for photos?

Yes, with limits. The tracer groups similar colours into the number you set, so a photo becomes flat colour regions without shading. Pictures with a clear subject and a plain backdrop give the most usable layers.

Why does my SVG import as one layer?

Design Space splits vector uploads into layers but keeps a raster upload as a single layer. If you uploaded a PNG or JPG, run it through this tool first and upload the SVG instead.

Do I need Cricut Access to upload SVG?

Cricut Access is Cricut’s subscription for its own library of images and fonts. A file you made yourself is a separate thing, but check Design Space for its current upload rules.

How is this different from uploading the image straight to Design Space?

A direct PNG or JPG upload stays one layer. Here the picture is traced first, so each colour is a separate path, holes such as the centre of an O stay open, and the background is gone.

Will the SVG cut cleanly on vinyl?

No file can promise that, because blade, mat and material matter too. Raising Smoothing and Smallest feature removes slivers a blade tends to tear, and a test cut on scrap shows the rest.

Can I convert a hand-drawn design?

Yes. Photograph the drawing in even light, raise Contrast so the lines stand out from the paper, and trace it with two or three colours.